Designed with contoured anti splash fronts to reduce
the risk of back splashing the units also have both
radiused internal and external corners for ease of
for superior hygiene.
Falcon scrub sinks are supplied complete with a
chrome plated 38 mm flush grated waste fitting, chrome
plated bottle trap and the appropriate number of sensor
modules, power packs, battery back up, low soap detector
probes, service panel, lockable front opening door for
soap bottle, wall mounting bracket and
Units are fully assembled and tested,
and pre-plumbed ready for connecting to the hot and cold
water services, mains power supply and the waste water
drain. (The waste water outlet can be either left or
lengths up to 3000 mm can be custom made to order.
Manufactured as standard in 304 grade and 16 gauge
stainless steel although units can be manufactured
in 316 grade material on request.
Wave hand across the red sensor disc and water will be
dispensed from the larger of the two nozzles to wet hands
first in line with correct hand washing procedures.
stop initial flow of water to dispense soap; cup
hand in front of the red sensor disc and below
nozzle to activate the soap dispenser lowering the
cupped hand when suffient soap has been delivered.
across the red sensor disc for water to be dispensed
for the timed period.
Repeat process if further water
or soap needs to be dispensed. The sensor disc detects
the hand at 60
The timed supply of water is factory set for
21 seconds, but can be easily adjusted for 14 or 7
Low Soap Detection
If the centre of the red sensor disc is flashing
then the soap bottle needs to be replaced.
When low soap is detected the unit will only
dispense four more times to prevent the soap
tubes being emptied. Once a new soap bottle
is fitted, dispensing will resume.
Green Power Light
If the green power light goes out then the power supply
has failed and the unit is on battery back up, consult
Comprises a stainless steel front panel with a back
box for recessed mounting into the 360 mm high splash
back. The chrome plated spout for the water and a smaller
stainless steel nozzle for the soap or antiseptic solutions,
are mounted into the front panel.
The soap nozzle is removable
so that it can be cleaned and disinfected.
A 25 mm diameter
dark red sensor disc in also located on the front panel,
which glows red in the centre
of the disc when activated.
The sensor module houses the spouts, sensor disc, soap
pump, solenoid valve PCB and the low soap warning system.
The sensor module is accessed from the front for ease
The removable service panels are located beneath the
scrub up trough and concealed in the rear box section.
service panel is easily lowered down from the unit
for service and maintenance.
The service panel houses
the power pack, battery back up and the thermostatic
Each station has it’s own sensor module,
service panel and front opening lockable soap door for
ease of changing over bottles and positioning the low
soap detector probe back into the replacement bottle.
The latest technology and easy to use, no touch infrared
sensor control for both soap and water operations. Pre
plumbed and pre wired ready for installation, thermostatic
valves to each station. Lockable front opening door with
clear operating instructions inscribed on the front of
the door. Battery back up fitted as standard.
corners to the trough and polished finish for ease
of maintenance and greater hygiene, with an anti
Hygienic no touch operation for dispensing both soap
and water. Cost savings for both water and soap usage.
Easy to maintain, reliable in use and user friendly.
Provides enhanced hygiene standards.
Connection to service panel (per station) 2
x 1/2 male BSP for hot and cold water supply. 1 x 1mm2
3 core mains flex for connection to 220/240 volt 50HZ AC
mains supply (via switched fused spur).
NOTE; 110 v 60 Hz AC can be accommodated if required.
Adjust thermostatic valve to required temperature,
(normally factory set at 43 degrees) all the internal
water and soap connections are pre plumbed. The electrical
12 volt DC supply is also pre-connected internally.
• All units can be supplied with an underneath
• Stainless steel removable station divider panels can also be provided